EnoughToGet CalculatorsGuides

Paint & plaster

How much paint per square metre?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

Using the calculator's starting spread rate of 16 square metres per litre in Australia (Dulux) or 11 in New Zealand (Resene example), a 3-metre by 3-metre room needs 3.52 litres in Australia or 5.12 litres in New Zealand for two coats, including a 10% waste allowance.

Try itPaint: enter your own sizes
m
Type metres, for example 4.2.
m
m
Each door is taken off the wall area.
Each window is taken off the wall area.
The ceiling uses the same paint here. Ceiling paint is often a different product.
Two coats is the usual advice on the label.
%
Covers rough surfaces and touch-ups.
You need
3.52 L
buy 4 L in cans

Shopping list

ItemBuyNote
Paint needed3.52 L2 coats over 25.6 m²
4 L can1 can4 L bought in total
  • Coverage is 16 m² per litre (Dulux calculator). Check the spread rate on your can: textured walls and dark colours use more.
How this was worked out
  1. Wall area: perimeter × height
    2 × (3 + 3) × 2.4 = 28.8 m²
  2. Minus openings: walls − doors × door area − windows × window area
    28.80 − 1 × 1.7 − 1 × 1.5 = 25.6 m²
  3. Paint needed: area × coats × (1 + waste) ÷ coverage
    25.60 × 2 × 1.10 ÷ 16 = 3.52 L

Understanding paint coverage

The amount of paint required for your project depends on the spread rate, which differs between Australia and New Zealand. According to the Dulux paint calculator, its estimates assume a spread rate of 16 square metres per litre. In contrast, the Resene paint calculator for New Zealand gives an example with a theoretical spreading rate of 11 square metres per litre and says to read the product data sheet. Dulux assumes two coats of topcoat, which it describes as the ideal number for most Dulux paints. Check the spread rate on your can before purchasing, as textured walls and dark colours use more paint. The calculator uses 16 for Australia and 11 for New Zealand as its starting values, so the same room needs more paint in New Zealand.

How it is worked out

The calculator determines the volume of paint needed by first establishing the total wall area. This is calculated by taking the perimeter of the room and multiplying it by the height. For a room with a length of 3 metres and a width of 3 metres, the perimeter is 12 metres, which, when multiplied by a height of 2.4 metres, results in a wall area of 28.8 square metres. From this total, the calculator subtracts the area of openings. It starts with a door area of 1.7 square metres and a window area of 1.5 square metres. For a room with one door and one window, the net area is 25.6 square metres. The final volume is then calculated by multiplying the net area by the number of coats, adding a 10% waste allowance, and dividing by the regional coverage rate.

Paint requirements by room size

The following table shows the paint needed for different room dimensions, using two coats, a 10% waste allowance, a wall height of 2.4 metres, and one door and one window in each room.

Room Size (m)RegionPaint Needed (L)
3 x 3AU3.52
3 x 3NZ5.12
4 x 4AU4.84
4 x 4NZ7.04
6 x 5AU6.82
6 x 5NZ9.92

Worked example

To calculate the paint needed for a 3-metre by 3-metre room in Australia, follow these steps using the calculator's working figures:

  1. Calculate the total wall area: 2 × (3 + 3) × 2.4 = 28.8 square metres.
  2. Subtract openings: 28.80 - 1 × 1.7 - 1 × 1.5 = 25.6 square metres.
  3. Determine the paint volume: 25.60 × 2 × 1.10 ÷ 16 = 3.52 litres.

The factor of 1.10 is the 10% waste allowance for touch-ups and spillage, so the final volume of 3.52 litres already includes it. Do not add waste a second time. For a project in New Zealand, the same area of 25.6 square metres is multiplied by 2 and by 1.10, then divided by 11 instead of 16, resulting in 5.12 litres.

Common mistakes

A frequent error is failing to subtract doors and windows. The calculator starts with an area of 1.7 square metres for a door and 1.5 square metres for a window. Another mistake is ignoring the difference in spread rates between Australia and New Zealand; using the wrong coverage figure will give you too little or too much paint. Finally, ensure you multiply the area by two coats rather than one, as the formula does. Round up to the cans the calculator lists. For 3.52 litres in Australia, buy one 4 litre can. For 5.12 litres in New Zealand, buy 6 litres as a 4 litre can plus a 2 litre can. Do not add the 10% waste again after reading the result, because it is already included.

Factors affecting your total

Several variables influence the final volume of paint required for your project. Textured walls and dark colours use more paint, so check the spread rate on your can. The calculator uses a 10% waste allowance for touch-ups and spillage, and you can edit it. If your room has more or fewer doors and windows than the default settings, adjust your area calculation accordingly. Resene describes its 11 square metres per litre as a theoretical spreading rate and says to read the product data sheet. Dulux says to check the can for its 16 square metres per litre. For anything this guide does not cover, check your product label or supplier.

Frequently asked questions

Why do I need two coats?

The calculator uses two coats because Dulux assumes two coats of topcoat, the ideal number for most Dulux paints.

What is the waste allowance for?

The 10% waste allowance is the calculator's starting value for paint lost to spillage or used for touch-ups, and it is already included in the results.

Can I use the same coverage rate for all paints?

No, check the spread rate on your product label or ask your supplier. The calculator uses 16 square metres per litre in Australia and 11 in New Zealand.

How do I account for doors and windows?

Subtract the area of your openings from the total wall area; the calculator starts with 1.7 square metres for a door and 1.5 square metres for a window.

What should I do if my room size is not listed?

Use the calculator on this site to enter your own room dimensions and get the volume for your project.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
paint coverage per litre16 m2/L
New Zealand: 11 m2/L
Verified 2026-11-18Dulux paint calculator page: estimates assume two-coat topcoat coverage at a spread rate of 16 m2 per litre (check the can).
paint coats2 coatsVerified 2026-11-18Dulux paint calculator page: assumes 2 coats of topcoat, the ideal number for most Dulux paints.
paint waste10 %Editable defaultcommon trade rule of thumb for touch-ups and spillage, editable
paint door area1.7 m2Editable defaultapprox. standard 2040 x 820 mm internal door, editable
paint window area1.5 m2Editable defaulttypical window opening, editable
paint can size 1l1 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 2l2 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 4l4 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 10l10 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 15l15 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.

Keep reading