EnoughToGet CalculatorsGuides

Concrete & masonry

How much concrete for a driveway?

By the EnoughToGet teamUpdated 2026-11-185 min readSources and assumptions

For the calculator's two driveway examples, order 2 m³ of ready-mix for a 6 × 3 m area at a 100 mm example thickness, or 5.6 m³ for a 12 × 3.5 m area at a 125 mm example thickness.

Try itConcrete slab: enter your own sizes
m
Type metres, for example 3.5.
m
The shorter side.
mm
100 mm is a common starting point for paths and patios. Driveways and sheds need a design for the load; check with your council or an engineer.
Yield per bag is about the same mix in every size, so the bag count changes but the volume does not. Check the yield on your bag.
%
Covers spills and uneven ground. You can change it.
Mesh is for slabs designed to carry loads. Ask for the design if you are unsure.
You need
2 m³
or 208 bags of 20 kg mix

Shopping list

ItemBuyNote
Ready-mix concrete2 m³ordered in 0.2 m³ steps
Crushed rock base (50 mm compacted, if used)2.16 t0.90 m³ compacted
  • Ready-mix suppliers often charge a short-load fee for small deliveries. Ask before you order.
How this was worked out
  1. Area: length × width
    6 × 3 = 18 m²
  2. Volume: area × thickness ÷ 1000
    18.00 × 100 ÷ 1000 = 1.8 m³
  3. With waste: volume × (1 + waste)
    1.800 × 1.05 = 1.89 m³
  4. Bags (20 kg): volume with waste ÷ yield per bag, rounded up
    1.890 ÷ 0.00909 = 207.9 bags
  5. Ready-mix: volume with waste, rounded up to the order step
    1.890 → steps of 0.2 m³ = 2 m³
  6. Base: area × base depth ÷ 1000 × compacted density
    18.00 × 50 ÷ 1000 × 2.4 = 2.16 t

How the quantity is worked out

The calculator multiplies the driveway's length by its width to get the area. It then multiplies that area by the thickness, dividing by 1,000 to convert millimetres to metres, which gives the concrete volume before waste. In the first example, 6 m by 3 m gives 18 m², and the 100 mm example thickness gives 1.8 m³. In the second, 12 m by 3.5 m gives 42 m², and 125 mm gives 5.25 m³.

Waste is added with the formula volume × (1 + waste). The waste value is 5%, matching the allowance Cement Australia's slab calculator page describes for wastage. Because the formula contains (1 + waste), the 1.89 m³ and 5.51 m³ results already include that allowance. The ready-mix order is then rounded up to 0.2 m³ steps, giving 2 m³ and 5.6 m³.

What changes the answer

A driveway carries vehicles, so its thickness and any reinforcing mesh need to come from a design, such as one prepared by an engineer or the council. The 100 mm and 125 mm figures in this guide are example inputs that show how thickness changes volume. They are not recommendations. Cement Australia gives 75 mm as the minimum for a non-load-bearing slab, which is a different situation from a driveway.

Length, width and thickness each change the volume directly. The second example has 42 m² of area, more than double the 18 m² of the first, and its thicker input raises the volume to 5.25 m³ before waste. The 5% waste allowance and the 0.2 m³ ordering step then adjust the final order.

Calculator quantities

Driveway areaExample thicknessReady-mix concrete20 kg bagsCrushed rock base (50 mm compacted, if used)
6 × 3 m100 mm2 m³208 bags2.16 t
12 × 3.5 m125 mm5.6 m³607 bags5.04 t

The ready-mix and bag figures are the calculator's headline results. The base figure applies only if a 50 mm compacted base is used. For a different base depth or driveway design, enter the matching dimensions into the calculator and check them against the design.

Worked example

The first example uses the calculator's working, step by step:

  1. Area: 6 × 3 = 18 m² [length × width; 6 × 3].
  2. Volume: 18.00 × 100 ÷ 1,000 = 1.8 m³ [area × thickness ÷ 1000; 18.00 × 100 ÷ 1000]. This is before waste.
  3. Waste: 1.800 × 1.05 = 1.89 m³ [volume × (1 + waste); 1.800 × 1.05]. This value already includes the 5% allowance, so do not add waste again.
  4. Bags: 1.890 ÷ 0.00909 = 207.9 bags, rounded up to 208 bags [volume with waste ÷ yield per bag, rounded up].
  5. Ready-mix: 1.890 rounded up to 0.2 m³ steps gives 2 m³.
  6. Base: 18.00 × 50 ÷ 1,000 × 2.4 = 2.16 t, if a 50 mm compacted base is used.

Bags, base and ready-mix ordering

Bag yields vary by product. Cement Australia's Concrete Mix product data sheet says 110 bags of 20 kg are required per cubic metre, while Boral's Concrete Mix product data sheet says 108 bags of 20 kg equate to one cubic metre. The calculator's bag comparison uses a yield of 0.00909 m³ per 20 kg bag, so check your product label or supplier before buying bags. For New Zealand products, Dricon (Firth) gives yields of 0.010 m³ for a 25 kg HandiCrete bag and 0.016 m³ for a 40 kg bag. Those yields apply to those bag sizes, not to 20 kg bags.

The examples round ready-mix to 0.2 m³ steps. Confirm that step with your supplier. The calculator also warns that ready-mix suppliers often charge a short-load fee for small deliveries, so ask about minimum orders and short-load fees before ordering.

Common mistakes

  • Treating an example thickness as a driveway recommendation. The 100 mm and 125 mm figures are example inputs only. A driveway carries vehicles, so its thickness and mesh need to come from a design.
  • Adding waste twice. The formula volume × (1 + waste) already applies the 5% allowance, so the 1.89 m³ and 5.51 m³ results already include waste; do not add it again.
  • Ordering the unrounded volume. The 1.89 m³ and 5.51 m³ figures round up to 2 m³ and 5.6 m³ in 0.2 m³ steps.
  • Mixing up volume and bag count. Cubic metres measure concrete volume, while bag counts depend on each product's yield.
  • Adding the base to the concrete. The crushed rock base is a separate estimate in tonnes, based on 50 mm compacted depth, and it cannot be added to cubic metres.

Frequently asked questions

How much concrete do I need for a 6 × 3 m driveway?

The calculator's example order is 2 m³ of ready-mix, using a 100 mm example thickness. That thickness is an input for the volume calculation, not a driveway recommendation.

How much concrete do I need for a 12 × 3.5 m driveway?

The calculator's example order is 5.6 m³ of ready-mix, using a 125 mm example thickness. The thickness should be confirmed by a design before you order.

Does the 75 mm minimum apply to a driveway?

No. Cement Australia gives 75 mm as the minimum for a non-load-bearing slab. A driveway carries vehicles, so its thickness and any mesh should come from an engineer or the council.

How many 20 kg bags do the examples need?

The calculator's headline figures are 208 bags for the first example and 607 bags for the second. Bag yields vary by product, so check your product label or supplier.

How much crushed rock base do the examples need?

If a 50 mm compacted base is used, the estimates are 2.16 t and 5.04 t. The base is a separate estimate and is not added to the concrete volume.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
concrete bags per m3 20kg cement australia110 bags/m3Verified 2026-11-18Cement Australia Concrete Mix product data sheet (PDS CM rev 3): 110 x 20 kg bags are required per cubic metre.
concrete bags per m3 20kg boral108 bags/m3Verified 2026-11-18Boral Concrete Mix product data sheet: 108 x 20 kg bags equate to one cubic metre of mixed concrete.
concrete bag yield 25kg0.01 m3Verified 2026-11-18Dricon (Firth) HandiCrete page: 25 kg bag yield 0.010 m3.
concrete bag yield 40kg0.016 m3Verified 2026-11-18Dricon (Firth) HandiCrete page: 40 kg bag yield 0.016 m3.
concrete slab waste5 %Verified 2026-11-18Cement Australia slab calculator page: calculation includes a 5% allowance for wastage and rounds bags up.
concrete slab thickness path100 mmEditable defaultcommon practice for paths and patios (Cement Australia how-to uses a 100 mm slab as its example), editable
concrete slab min thickness75 mmVerified 2026-11-18Cement Australia slab calculator page: minimum thickness for a non-load bearing slab would be 75 mm (consult a professional for loads).
concrete readymix order step0.2 m3Editable defaulttypical ready-mix ordering granularity, rule of thumb, editable; confirm with local plant
concrete readymix consider m31 m3Editable defaultRule of thumb: above about 1 m3 a ready-mix delivery is usually easier than mixing bags. Editable; ask your supplier about minimum orders and short-load fees.
concrete base depth50 mmVerified 2026-11-18Cement Australia how to lay a concrete slab: excavate an extra 5 cm and compact crusher dust or road base to 5 cm.
landscape density roadbase compacted2.4 t/m3Verified 2026-11-18Australian Native Landscapes product weights FAQ: road base/DGB/FCR 2.4 t/m3 (compacted figure).
concrete mesh effective length5.8 mVerified 2026-11-18InfraBuild ribbed square mesh page: SL72 and SL82 effective area 5.8 x 2.4 m.
concrete mesh effective width2.4 mVerified 2026-11-18InfraBuild ribbed square mesh page: SL72 and SL82 effective area 5.8 x 2.4 m.

Keep reading