EnoughToGet CalculatorsGuides

Landscaping

How many pavers per square metre?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

For a one-square-metre area, allow 7 pavers at 400 × 400 mm, 5 at 600 × 400 mm or 50 at 200 × 100 mm, using the calculator’s shopping quantities.

Try itPavers: enter your own sizes
m
Type metres, for example 4.5.
m
The shorter side.
Pavers per square metre include the joints, from Adbri Masonry paving data.
%
Patterns and curves need more.
You need
7 pavers
1.0 m² at 6.25 per m²

Shopping list

ItemBuyNote
Pavers, 400 × 400 mm7 pavers6.25 per m² including joints
Road base (75 mm compacted depth)0.18 t0.07 m³
Bedding sand (25 mm)0.04 t0.03 m³
  • Allow a fall of at least 2% for drainage, and dig about 170 mm deep for a patio base, bedding sand and the paver.
How this was worked out
  1. Area: length × width
    1 × 1 = 1 m²
  2. Pavers needed: area × pavers per m²
    1.00 × 6.25 = 6.25 pavers
  3. With waste: pavers × (1 + waste), rounded up
    6.3 × 1.00 = 6.25 pavers
  4. Road base: area × depth ÷ 1000 × density
    1.00 × 75 mm × 2.4 t/m³ = 0.18 t
  5. Bedding sand: area × depth ÷ 1000 × density
    1.00 × 25 mm × 1.45 t/m³ = 0.04 t

How pavers per square metre are worked out

The calculator works out area by multiplying length by width, then multiplies that area by the paver rate per square metre. For a one-square-metre patio, the area is 1 m², so the rate is also the paver count before rounding.

Adbri Masonry’s paving brochure gives these rates: 6.25 pavers per m² for 400 × 400 mm Euro Stone, 4.16 per m² for 600 × 400 mm Euro Stone, 12.50 per m² for 400 × 200 mm Havenslab, and 50 per m² for 200 × 100 mm Havenbrick. The rates describe each named product and size; check your product label or supplier if yours differs.

The calculator’s shopping quantities round up to whole pavers. That is why a rate with a fraction can result in a purchase quantity above the unrounded count.

One-square-metre patio table

The calculator’s results below use a 1 m² area and zero waste. They give the paver shopping quantity alongside the road base and bedding sand quantities calculated for the same area. The table covers the three sizes with calculator outputs; the brochure’s 400 × 200 mm rate is given above.

Patio areaPaver sizePavers per m²Pavers to buyRoad baseBedding sand
1.0 m²400 × 400 mm6.257 pavers0.18 t0.04 t
1.0 m²600 × 400 mm4.165 pavers0.18 t0.04 t
1.0 m²200 × 100 mm5050 pavers0.18 t0.04 t

For a different patio area, enter its length and width in the calculator. The table does not calculate quantities for other patio areas.

Worked example

For the first example, the calculator uses a length of 1 m and a width of 1 m. First, it calculates area using “length × width”: 1 × 1 = 1 m².

Next, it calculates pavers needed using “area × pavers per m²”: 1.00 × 6.25 = 6.25 pavers. The result then applies “pavers × (1 + waste), rounded up”: 6.25 × 1.00 = 6.25 pavers with zero waste. This formula includes the waste factor; because the example uses zero waste, it adds no allowance.

For the materials, road base uses “area × depth ÷ 1000 × density”: 1.00 × 75 mm × 2.4 t/m³ = 0.18 t. Bedding sand uses the same formula with its values: 1.00 × 25 mm × 1.45 t/m³ = 0.04 t. The shopping list rounds 6.25 pavers up to 7.

What changes the answer

The patio area changes the count: the calculator uses length multiplied by width before applying the paver rate. The paver size also matters because each size has a different rate per square metre. For the same 1 m² area, the calculator’s results range from 5 pavers for 600 × 400 mm to 50 for 200 × 100 mm.

Waste changes the paver quantity through the formula “pavers × (1 + waste), rounded up”. The examples use zero waste. Separately, Adbri Masonry’s Ultimate Outdoor Planning Guide, with the Concrete Masonry Association of Australia, advises ordering an extra 5% for cuts and breakages. If you use a waste allowance, enter it in the calculator rather than adding it again to a result that already includes it.

Common mistakes

One arithmetic mistake is to use the paver’s dimensions as though the count were the same for every size. The brochure rates differ: 6.25 pavers per m² for 400 × 400 mm and 50 per m² for 200 × 100 mm. Check the exact size and product name before using a rate.

Another mistake is treating a fractional paver count as a purchase quantity. The calculator’s 400 × 400 mm result begins at 6.25 pavers and rounds the shopping list up to 7. Do not round down.

Keep waste and units clear. The calculator examples use zero waste, while Adbri Masonry’s Ultimate Outdoor Planning Guide advises an extra 5% for cuts and breakages. For the material quantities, the calculator uses millimetres for depth and tonnes for road base and bedding sand; avoid mixing those units in the formula.

Patio quantities and the calculator

The table is limited to 1 m² because that is the patio area in these calculator examples. It is not a set of quantities for larger patio footprints. For another area, use the patio’s measured length and width in the calculator; the paver count depends on both the area and the selected paver rate.

For the same example area, the calculator uses 75 mm compacted depth for road base and 25 mm bedding sand, producing 0.18 t and 0.04 t respectively. Adbri Masonry’s brochure gives those depths for its flexible installation information. The brochure also says to allow a minimum 2% gradient and to excavate approximately 170 mm deep. Check your product label or supplier if the product information differs.

Frequently asked questions

How many 400 × 400 mm pavers do I need per m²?

Adbri Masonry gives a rate of 6.25 per m²; the calculator’s one-square-metre shopping quantity is 7 pavers.

How many 600 × 400 mm pavers do I need per m²?

The brochure rate is 4.16 per m², and the calculator’s shopping quantity for 1 m² is 5 pavers.

How many 400 × 200 mm pavers do I need per m²?

Adbri Masonry gives 12.50 Havenslab pavers per m²; check your product label or supplier if your product differs.

How many 200 × 100 mm pavers do I need per m²?

The brochure rate is 50 Havenbrick pavers per m², matching the calculator’s 50-paver quantity for 1 m².

Does the calculator’s paver quantity include waste?

The examples use zero waste. The formula applies the waste factor when entered, while Adbri Masonry’s guide advises an extra 5% for cuts and breakages.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
paver per m2 400x4006.25 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Euro Stone 400 x 400 x 40 mm, 6.25 units per m2.
paver per m2 600x4004.16 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Euro Stone 600 x 400 x 40 mm, 4.16 units per m2.
paver per m2 400x20012.5 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Havenslab 400 x 200 x 40 mm, 12.50 units per m2.
paver per m2 200x10050 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Havenbrick 200 x 100 x 40 mm, 50 units per m2.
paver waste5 %Verified 2026-11-18Adbri Masonry Ultimate Outdoor Planning Guide: with the Concrete Masonry Association of Australia, order an extra 5% for cuts and breakages.
paver roadbase depth75 mmVerified 2026-11-18Adbri Masonry paving brochure (VIC) flexible installation: compacted road base min 75 mm (also 'enough for 75 mm compacted depth' in its how-to checklist).
paver bedding sand depth25 mmVerified 2026-11-18Adbri Masonry paving brochure (VIC) flexible installation cross section: bedding sand nominal 25 mm (its how-to checklist allows sand for 30 mm).
paver excavation depth170 mmVerified 2026-11-18Adbri Masonry paving brochure (VIC) how to lay pavers, step 1: excavate approx. 170 mm deep.
paver min fall2 %Verified 2026-11-18Adbri Masonry paving brochure (VIC): minimum gradient 2% (100 mm per 5 lineal metres).
landscape density roadbase compacted2.4 t/m3Verified 2026-11-18Australian Native Landscapes product weights FAQ: road base/DGB/FCR 2.4 t/m3 (compacted figure).
landscape density sand brickies1.45 t/m3Verified 2026-11-18Australian Native Landscapes product weights FAQ: brickies sand 1.45 t/m3.

Keep reading