Concrete & masonry
How many bricks per square metre?
For a single skin wall built from 230 x 76 mm bricks with 10 mm joints, allow about 48.5 bricks per square metre; the same wall in double brick takes about 97 bricks per square metre before any waste allowance is added.
Shopping list
| Item | Buy | Note |
|---|---|---|
| Bricks | 49 bricks | 48.4 per m² per skin |
| Mortar mix, 20 kg bags | 3 bags | about 33 L of mortar |
- Bricks per m² is worked out for 230 × 76 mm bricks with 10 mm joints (about 48.5 per m², Littlehampton Brick). Other brick sizes need other numbers: check your brick's data sheet.
- Mortar: Cement Australia says a 20 kg bag of Mortar Mix lays about 20 bricks. Other calculators quote far fewer bags, so check your own mortar bag.
How this was worked out
- Wall area:
length × height − openings
1 × 1 − 0 = 1 m² - Bricks per m²:
1 ÷ ((brick length + joint) × (brick height + joint))
1 ÷ (0.24 × 0.086) = 48.45 bricks/m² - Bricks needed:
area × bricks per m² × skins × (1 + waste), rounded up
1.00 × 48.45 × 1 × 1.00 = 48.45 bricks - Mortar mix:
bricks × (1 + mortar waste) ÷ bricks per bag, rounded up
49 × 1.10 ÷ 20 = 2.7 bags (20 kg)
How the bricks per square metre figure is worked out
Littlehampton Brick gives the work size of an Australian clay brick as 230 x 110 x 76 mm, with bricks per square metre counted at 10 mm mortar joints. The calculator uses 230 mm and 76 mm from that work size and adds the joint to both directions. Its formula is "1 ÷ ((brick length + joint) × (brick height + joint))", with the numbers put in as 1 ÷ (0.24 × 0.086). That gives 48.45 bricks/m². Littlehampton Brick's own figure is 48.5 bricks per square metre including mortar, so the two agree once you allow for rounding. For 1 m² the calculator reports 49 bricks after rounding up.
What changes the answer
The calculator multiplies wall area by bricks per m², by the number of skins, then by "(1 + waste)". A single skin uses 1; a double brick wall uses 2, which turns 48.45 into 96.9 and rounds to 97 bricks for 1 m². Waste is an editable allowance. Littlehampton Brick says 50 bricks per square metre once 3% wastage is added. Other sources suggest 5 to 10% for cuts and breakage, so change the waste figure if your job has many cuts. Brick size also changes the count: 48.5 is for 230 x 76 mm bricks with 10 mm joints, and other brick sizes need other numbers, so check your brick's data sheet. The calculator applies a 10% mortar waste allowance for spills and dropped mortar.
Bricks and mortar for the calculator's three cases
The table sets out the calculator's three cases: 1 m² single skin, 1 m² double skin, and 10 m² single skin with waste. The mortar column uses Cement Australia's figure that one 20 kg bag lays about 20 bricks, plus the calculator's starting value of 10% mortar waste, rounded up.
| Case | Wall area | Bricks per m² | Bricks to buy | Mortar mix, 20 kg bags |
|---|---|---|---|---|
| Single skin, no waste | 1.0 m² | 48.45 | 49 bricks | 3 bags |
| Double skin, no waste | 1.0 m² | 48.45 | 97 bricks | 6 bags |
| Single skin, 3% waste | 10.0 m² | 48.45 | 500 bricks | 28 bags |
Worked example: 1 m² single skin wall
Start with the wall area: length × height − openings gives 1 × 1 − 0 = 1 m². Next, bricks per m²: 1 ÷ ((0.24) × (0.086)) = 48.45 bricks/m². Then bricks needed: area × bricks per m² × skins × (1 + waste), with the numbers 1.00 × 48.45 × 1 × 1.00 = 48.45, rounded up to 49 bricks. The waste entry is 0, so the (1 + waste) factor is 1.00; the waste allowance inside that factor is zero. Mortar: bricks × (1 + mortar waste) ÷ bricks per bag, using 49 × 1.10 ÷ 20 = 2.7 bags, rounded up to 3 bags of 20 kg. The 1.10 factor includes the 10% mortar waste.
Common mistakes
Do not divide the wall area by 48.45; the calculator multiplies area by bricks per m². Keep the units consistent and include the joint: the formula uses 0.24 m (230 mm + 10 mm) and 0.086 m (76 mm + 10 mm), not 230 and 76. If the waste field is 3%, the factor is 1.03 and already includes the allowance; adding 3% again overstates the order. Round up the bricks needed, not down: 499.03 becomes 500, and 96.9 becomes 97. A double brick wall uses two skins, so the single-skin figure of 48.45 is doubled before waste. For mortar, the bag count uses Cement Australia's 20 bricks per 20 kg bag and a 10% mortar waste factor; the same data sheet gives about 11 litres per 20 kg bag, so do not mix up litres and bags.
Frequently asked questions
How many bricks per square metre for a single skin wall?
About 48.5 bricks per square metre for 230 x 76 mm bricks with 10 mm joints. The calculator works it out as 48.45 and reports 49 bricks for 1 m².
How many bricks per square metre for a double brick wall?
About 97 bricks per square metre. The calculator uses two skins: 1.00 × 48.45 × 2 × 1.00 = 96.9, rounded up to 97 bricks for 1 m².
Does the 3% waste allowance change the 48.5 figure?
It changes the number you buy, not the bricks per m². Littlehampton Brick says 50 bricks per square metre once 3% wastage is added. In the calculator the waste sits inside the "(1 + waste)" factor: at 3% the factor is 1.03, so do not add a second 3%.
How many 20 kg bags of mortar mix do I need?
Cement Australia says one 20 kg bag of Mortar Mix lays about 20 bricks at a 10 mm joint. With 10% mortar waste, the calculator gives 3 bags for 49 bricks, 6 bags for 97 bricks and 28 bags for 500 bricks.
Do other brick sizes use the same count?
The 48.5 bricks per square metre figure is for 230 x 76 mm bricks with 10 mm joints. Other brick sizes need other numbers, so check your brick's data sheet.
Sources and assumptions
These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.