EnoughToGet CalculatorsGuides

Fencing & decking

How many Colorbond fence panels do I need?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

For a 20-metre fence using 2350 mm wide steel panels, you will need 9 panels, 10 posts, 27 sheets, and 20 bags of post mix concrete.

Try itFence: enter your own sizes
m
The total length of the fence line, gates included.
mm
Up to 1800 mm. Check your council for height limits near boundaries.
Steel panels follow the Lysaght fence installation guide.
mm
Timber shrinks, so many builders leave a small gap. 0 means edge to edge.
You need
10 posts
for 20 m of fence

Shopping list

ItemBuyNote
Steel 3-sheet panel (2350 mm wide)9 panels3 sheets each
Steel fence sheets27 sheetsCheck the sheet height with your supplier
Posts10 postsPost spacing equals the panel width
Post Mix concrete, 20 kg bags (post holes)20 bags2 bags a hole, for a hole 2 × the post width
  • Steel fence height and post size depend on wind region. Check the Lysaght guide or your supplier.
  • The 2-bag figure is Bunnings Post Mix advice for a hole 2 × the post width. A wider or deeper hole needs more bags.
How this was worked out
  1. Panels: length ÷ panel width, rounded up
    20000 ÷ 2350 = 9 panels
  2. Posts: panels + 1
    9 + 1 = 10 posts
  3. Sheets: panels × sheets per panel
    9 × 3 = 27 sheets
  4. Concrete for posts: posts × bags per hole
    10 × 2 = 20 bags

Understanding panel requirements

When planning a steel fence, the total length of your boundary determines the exact number of panels required. Using the Lysaght fence and gate installation guide for non-cyclonic regions, a 3-sheet panel has a width of 2350 mm. To calculate the number of panels, divide your total fence length by the panel width and round up to the nearest whole number. For a 20-metre fence, this results in 9 panels. For a 30-metre fence, you require 13 panels. Because each panel consists of 3 individual sheets, you must multiply the number of panels by 3 to determine the total sheet count. This ensures you have enough material to cover the entire span of the fence line without coming up short. A separate configuration using the 4-sheet panel has a width of 3100 mm, which changes the total panel and sheet counts for the same boundary length. Steel fence height and post size depend on your wind region, so check the Lysaght guide or your supplier.

Post and concrete calculations

The calculator works out posts as the number of panels plus 1. For a 20-metre fence using 9 panels, you need 10 posts. For a 30-metre fence using 13 panels, you need 14 posts. Regarding the foundation, the Bunnings Easy Mix Post Mix technical data sheet advises using approximately two 20 kg bags per post hole, assuming a hole width that is twice the width or diameter of the post. Therefore, you multiply your total post count by 2 to find the number of bags required. For 10 posts, you need 20 bags, and for 14 posts, you need 28 bags. If your post holes are wider or deeper than this, you will need more concrete. Check your product label or supplier if your hole dimensions differ from the hole width factor Bunnings gives.

Summary of materials

The following table outlines the quantities needed for different fence lengths using the 2350 mm wide 3-sheet panel configuration and the 3100 mm wide 4-sheet panel configuration.

Fence LengthStylePanelsPostsSheetsConcrete (20 kg bags)
20 metresSteel 3-sheet panel (2350 mm wide)9102720
30 metresSteel 3-sheet panel (2350 mm wide)13143928
20 metresSteel 4-sheet panel (3100 mm wide)782816

Worked example

To calculate the materials for a 20-metre fence using 3-sheet panels, follow these working steps from the calculator. First, determine the panel count by dividing the total length of 20000 mm by the panel width of 2350 mm, which equals 9 panels when rounded up using the formula length divided by panel width. Second, determine the post count by adding 1 to the panel count, resulting in 10 posts using the formula panels plus 1. Third, determine the sheet count by multiplying the 9 panels by 3 sheets per panel, resulting in 27 sheets using the formula panels multiplied by sheets per panel. Fourth, determine the concrete requirement by multiplying the 10 posts by 2 bags per hole, resulting in 20 bags of post mix using the formula posts multiplied by bags per hole. Check your product label or supplier if your specific site conditions vary from these dimensions.

Common mistakes

A frequent error in calculating fence materials is failing to account for the final post in a run. The calculator works out posts as the number of panels plus 1, so 9 panels need 10 posts, not 9. Another mistake is underestimating the concrete needed for the post holes. The 2-bag figure from the Bunnings Easy Mix Post Mix technical data sheet is based on a hole width that is 2 times the width or diameter of the post. If you dig a wider or deeper hole, you will need more than 2 bags per post. Additionally, ensure you are using the correct panel width for your specific product. While the 3-sheet panel is 2350 mm wide, the 4-sheet panel is 3100 mm wide, and the 2-sheet panel is 1582 mm wide according to the Lysaght fence and gate installation guide. Using the wrong width in your division will result in an incorrect material list.

Frequently asked questions

Does the fence height affect the number of panels?

The number of panels is determined by the total length of the fence and the width of the panels, not the height. However, steel fence height and post size depend on your wind region, so check the Lysaght guide or your supplier.

How many bags of concrete do I need per post?

The Bunnings Easy Mix Post Mix technical data sheet advises using approximately two 20 kg bags per post hole, assuming a hole width that is 2 times the width or diameter of the post.

What is the width of a 4-sheet steel panel?

According to the Lysaght fence and gate installation guide for non-cyclonic regions, a 4-sheet panel is 3100 mm wide.

Are posts included in the panel count?

Posts are calculated separately, where the total number of posts is equal to the number of panels plus 1.

What if my fence length is not an exact multiple of the panel width?

You must divide your total length by the panel width and round up to the nearest whole panel to ensure you have enough material to cover the entire boundary.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
fence timber post spacing max2.4 mVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: rails 100 x 38 mm allow 2400 mm max post spacing (2100 mm with 75 x 38 mm rails).
fence timber rails up to 12002 railsVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: two rails for paling fences up to 1200 mm high.
fence timber rails over 12003 railsVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: fences over 1200 mm and up to 1800 mm high require three rails.
fence paling width 100100 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: commonly used paling sizes are 100 x 15 mm and 75 x 15 mm.
fence paling width 7575 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: commonly used paling sizes are 100 x 15 mm and 75 x 15 mm.
fence paling gap default0 mmEditable defaultPalings are laid edge to edge by default. Timber shrinks, so many builders leave a small gap; type your own gap.
fence steel panel width 2sheet1,582 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 1582 mm with 2 infill sheets.
fence steel panel width 3sheet2,350 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 2350 mm with 3 infill sheets (post spacing = panel width).
fence steel panel width 4sheet3,100 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 3100 mm with 4 infill sheets.
concrete post bags per hole2 bags (20 kg)Verified 2026-11-18Bunnings Easy Mix Post Mix technical data sheet: use approximately two 20 kg bags per post hole.
concrete post hole width factor2 x post widthVerified 2026-11-18Bunnings Easy Mix Post Mix technical data sheet: hole width = 2 x width or diameter of the post.
fence timber post depth600 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: posts about 600 mm deep for fences 1200-1800 mm high (450 mm up to 1200 mm).

Keep reading